The "type" command is used to indicate the type of ephone that is being configured. #CISCO 7941 RING TONE DOWNLOAD MAC#If you are connecting a softphone to the system, you would use your PC's MAC address. Normally MAC addresses are formated: 00:1B:53:5C:FC:66 or 00-1B-53-5C-FC-66 but Cisco breaks the MAC address into this format 66. Only phones that are identified here by their MAC address are allowed to use the phone system. Very strange! Just a note, there is still more configuration to make MoH work. Enter in "multicast-moh" and the line disappears and nothing replaces it. When you first run this setup, there will be a line "no multicast-moh" present. Type 7960 model of phone for firmware loadingīutton 1:1 Line 1 uses dialing number 1īy default, Music on Hold (MoH) is disabled for some stupid reason for each phone. This is an example of a bare bones ephone configuration:Įphone 1 indicates the first phone to configure The first physical phone is "ephone 1", the next is "ephone 2", etc. On no answer (noan) after 10 seconds call forward to the voicemail pilot number.Įxamine the physical phone configuration under the command "ephone x". The voicemail pilot number will bring up the voicemail service. What happens if the extension is busy? You call forward the caller to another extension or in this case to the voicemail pilot number. This assigns the actual number that would be dialed to reach the phone. The dual-line option allows call transfers, paging, call waiting and a host of other services. Number 2201 assigns the extension or dialing numberĬall-forward busy 2200 when busy forward to the voicemail pilot numberĬall-forward noan 2200 timeout 10 on no answer go to voicemail pilot number Here's an example of the first extension configuration:Įphone-dn 1 dual-line this indicates the first (1) extension The first extension is "ephone-dn 1", the next "ephone-dn 2", etc. The command ephone-dn stands for " electronic phone dialing number" or as it is commonly known as the "extension" number. After the initial setup, I prefer to assign any new extensions through the CME GUI and remove this command. I have mixed feelings about this command as I've had instances where I've had to take the whole system down and then when CME and the phones rebooted, all of the phone's dialing numbers changed! So it was like all of the extensions were randomly assigned depending on which phone booted first. If there were more phones, you could change it to "auto assign 1 to 10". The ephone and ephone-dn commands will be auto populated with information. This command allows CME to auto configure the phones as they are physically connected. The port indicates the UDP port that is used by the SCCP protocol which is port 2000. All phones will register to this IP address. This command specifies which IP address that CME will use for voice communications - it should be on the Voice VLAN. If you want to add another phone then you will need to increase the number of dialing numbers too. This command sets the maximum number of dialing numbers (extensions) that CME will allow. If more phones were required, you could manually issue the command with however many phones you need. During the initial setup, only 2 were indicated. This command sets the maximum number of physical phones that are allowed to connect to CME. This way you can specify specific firmware for different models if needed. #CISCO 7941 RING TONE DOWNLOAD SERIES#In this case, its for the 79 series of phones. This command identifies the firmware to load for specific phone models. The following configuration is a bare bones example of the telephony-service section: The actual telephony commands are scattered through-out the running configuration and are not limited to the telephony-service section. The IP phone configuration starts in the telephony-service section of the running configuration. It is important that you familiarize yourself with the command line configuration as CME lives half in the GUI and the other half in the command line. They are located in the telephony-service section. On your router, examine your running config to see the telephony changes added.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |